DOOR ACCESS 712 BASIC SETUP CONFIGURATION WIRELINE DIGRAM CONNECTIVITY

CHANGE PROGRAMMING PASSWORD #PROGRAMMING #0 NEW PASSWORD #
(IF PROGRAMMING PASSWORD LOST ,PERFORM 3.2 RESET TO FA
CTORY DEFAULT (123456)

ADD USER #PROGRAMMING #1 READ

ADD IF ADD MULTI C
ADD , READ

ADD #
ADD CONTINUOUSLY
SET COMMAND ACCESS
COMMAND ACCESS PASSWORD #PROGRAMMING #21 NEW
COMMON ACCESS PASSWORD #
ACCESS PASSWORD IS ONLY ONE , OPEN METHOD : COMMAND PASSWORD #
DELETE ALL USER #PROGRAMMING #40 0000 #
DELETE ALL C
ARD AND PIN EXCEPT COMMON ACCESS PASSWORD
DELETE USER BY READ
IF DELETE MULTI C
C
ADD , READ
ADD #PROGRAMMING #41 READ
CARD
CONTINUOUSLY

DISCHARGE FRONT BOARD AND
"TEN" -LIKE SCREW IN BOTTOM BOARD, THEN TAKE OFF BOTTOM BOARD, ASSEMBLE BOTTOM BOARD IN SIDE
OF ENTRY WITH PLASTIC INSERTS AND SCREWS.
HOW TO CONNECT ELECTRIC
AL WIRE:
CONNECT WIRE WITH REFERENCE TO ROUTINE MARK IN ELECTRIC
AL BOARD.
C
AUTION! BEFORE POWER ON, MUST CHECK VOLTAGE OF POWER SUPPLIER AND
C
ATHODE AND POSITIVE
REMARK:
W
ARNING ALARM SWITCH IS AT RIGHT BOTTOM SIDE, VOICE DIED
BUZZER AND MAKE CONTINUOUS W
ARNING.
WITH DOOR CLOSED, THEN SPRING OUT
PROGRA
MMING
GUIDE
EXP
AND
FUNSTION
OPERATION GUIDELINES
CCESS CONTROLLER INITIALIZATION:
AFTER POWER OFF, CONNECT BIN 2 AND BIN 3 OF RESET SUPPLY POWER, BUZZER MAKE CONTINUOUS
W
ARNING ALARM, POWER LIGHT(RED LIGHT), OK(GREEN) LIGHT AND MODE(ORANGE) LIGHT ALL FLASH.
CUT OFF POWER, THEN CONNECT POWER SUPPLY, ALL LIGHTS, INCLUDING POWER, OK AND MODE, FLASH,
W
AITING FOR EXCHANGING PEST SWITCH
BIN 2 AND BIN3 DISCONNECTED, BIN 1 AND BIN CONNECTED.
CCESS CONTROLLER INITIALIZATION IS COMPLETED, AFTER A VOICE OF BUZZER, CONTROLLER WILL BE
AVAILABLE FOR USER.

REMARK:
WORK).OTHER DATA
INITIALIZATION ONLY MODIFY SYSTEM PASSWORD TO DEFAULT PASSWORD(DEFAULT WHEN EX-
WILL NOT CHANGED.
ELECTRICAL LOCK ASSEMBLING:
WHEN CONNECT BIN 1 AND BIN 2, OPEN SIGNAL IS OUTPUTTED( POWER ON AND DOOR OPEN); WHEN
CONNECT BIN 2 AND BIN 3, CLOSE SIGNAL IS OUTPUTTED(POWER OFF AND DOOR CLOSED); DRIVE VOLTAGE
FOR ELECTRIC
AL LOCK IS 17V

HOW TO SET UP ACCESS CONTROLLER SYSTEM PROGRAM.
"#" KEY: FUNCTION KEY, GO INTO SYSTEM EDIT MODE PUSH" #", THEN RED, GREEN AND ORANGE LIGHTS ALL
WORK. INPUT 5 SYSTEM PASSWORDS AND A VOICE OF BUZZER IS MADE.
"O" KEY: LOG ON USER C
ARD PLUS PASSWORD
PUSH" O" KEY,ORANGE LIGHT LIGHTS, RED AND GREEN LIGHTS DIE INPUT 4
DIGITAL USER NO.VALID. AFTER
READING USER C
ARD, A BUZZER INVOICE HAPPENED, THEN AGAIN INPUT 6
DIGITALS PASSWORD, A LONG
BUZZER VOICE HAPPENED, GREEN LIGHTS DIED AFTER FLASH, ORANGE AND RED LIGHT LIGHTS AND USER
LOGGED ON SUCCESSFULLY.
"I" KEY: MODIFY SYSTEM PASSWORD
PUSH" I" , ORANGE LIGHT LIGHTS, RED AND GREEN LIGHTS DIE. USER INPUTS 5 DIGIT NUMBER PASSWORD
(SUCH AS 23456), ONCE INPUT COMPLETED, BUZZER MAKES A SHORT VOICE, GREEN LIGHT DIED AFTER
FLASH, RED LIGHT AND ORANGE LIGHTS LIGHT, THEN MODIFIC
ATION OF PASSWORD IS SUCCESSFUL.
CAUTION: PLEASE USER KEEP PASSWORD
WELL. WHEN YOU GO INTO SYSTEM PROGRAM MODE
AGAIN, NEED INPUT THE PASSWORD, IF FORGET IT, PLEASE EXECUTE INITIALIZATION PROCESS.
"2" KEY: LOG ON USER C
ARD, OR PASSWORD
PUSH" 2" KEY, ORANGE LIGHT LIGHTS, RED AND GREEN LIGHTS DIE INPUT 4
DIGITAL USER NO., GREEN LIGHT
LIGHTS, SHOWING USER NO. VALID. IF BUZZER MAKES 3 INVOICES, SHOWING THAT THE USER NO. ALREADY
LOGGED ON; IF BUZZER MAKE 4 LONG CONTINUOUSLY VOICES, SHOWING MEMORY IS FULL, C
AN' T LOG ON.
AFTER READING USER C
ARD, OR INPUTTING 6
DIGITAL PASSWORD, GREEN LIGHT DIED AFTER FLASH;
ORANGE AND RED LIGHTS LIGHT AND USER LOGGED ON SUCCESSFULLY. IF BUZZER MAKE 3 CONTINUOUS
VOICES, SHOWING THAT THE C
ARD OR PASSWORD ALREADY LOGGED ON, C
AN'T REPEATEDLY LOG ON
"3" KEY: DELETE SOLO USER C
ARD OR PASSWORD, OR C
ARD PLUS PASSWORD.
PUSH" 3" KEY, ORANGE LIGHT LIGHTS, RED AND GREEN LIGHTS DIED. INPUT 4
DELETED, A LONG BUZZER IS MADE
DIGITAL NUMBER TO BE

"A" KEY: DELETE ALL USER C
ARD OR PASSWORD OR C
AR PLUS PASSWORD PUSH" 4" A LONG BUZZER IS
MADE, GREEN LIGHT DIE AFTER FLASH, ORANGE AND RED LIGHTS LIGHT, SHOWING ALL USER DATA ARE
DELETED
"5" KEY: SET UP TIME OF OPENING DOOR.
PUSH" 5" , ORANGE LIGHT LIGHTS, RED AND GREEN LIGHTS DIED. INPUT 2 DIGITAL NUMBER FOR OPEN DOOR
TIME, BUZZER MAKE A LONG VOICE, GREEN LIGHT DIED AFTER FLASH, ORANGE AND RED LIGHTS LIGHT, THE
TIME OF OPEN DOOR IS SET UP SUCCESSFULLY.
"G" KEY CONTINUOUSLY W
ARRANT THE C
AR OF CONSUMERS
A , PRESS" 9" KEY, RED LIGHT OUT
B, INPUT FOUR CONSUMERS'
NUMBERS OF THE FIRST C
ARD, GREEN LIGHT ON, THE INPUTTED NUMBERS IS VALID
C, CONTINUOUSLY IDENTIFY THE C
ARS THAT ARE GOING TO BE W
ARRANTED (THE C
ARS' NUMBER
INCREASE BY DEGREES ) , PRESS"
#" KEY IN THE END TIME
"6" KEY:EXIT KEY.
BUZZER MAKES A LONG VOICE, GREEN LIGHT DIE AFTER FLASH, RED LIGHT LIGHTS, ORANGE LIGHT DIES,
CCESS CONTROLLER EXITS FROM SYSTEM PROGRAM MODE AND GOES INTO NORMAL WORK MODE. THE
SYSTEM PASSWORD PROVIDED
WITH THE LOCKING-MA
CHINE FUNCTION. THE SPECIFIC OPERATION IS : INPUT
THE PROGRAMME CODE + "#" + "8" , AND THEN THE A
CCESS CONTROL MA
CHINE WILL
STAND IN LOCKING STATE, NO C
AR AND
CODE WILL BE VALID. REPEATING THE SAME OPERATION 
ANCEL THE LOCKING STATE. DESCRIPTION: DURING SYSTEM PROGRAM PROCESS, IF TYPE ERROR OR
WRONGLY APERATION, CONTROLLER WILL MAKE W
ARNING ALARM FOR INCIDENT WITH 3 LONG BUZZERS
AND RETURN TO NORMAL USE STATUS. IF 5 2-SHORT-1-LONG BUZZERS ARE MADE, SHOW SYSTEM MEMORY
READS WRONGL

🌐 www.hikvisionisd.com